Pilz PNOZ mm0p-T Manual do Utilizador

PNOZ mm0p-TOperating Manual-1002704-EN-01Configurable Control System PNOZmulti

SafetyOperating Manual PNOZ mm0p-T 1002704-EN-0110SafetyIntended useThe configurable control system PNOZmulti is used for the safety-related interrupt

SafetyOperating Manual PNOZ mm0p-T 1002704-EN-0111Safety regulationsUse of qualified personnelThe products may only be assembled, installed, programme

Function descriptionOperating Manual PNOZ mm0p-T 1002704-EN-0112Function descriptionDevice propertiesIntegrated protection mechanismsThe relay conform

InstallationOperating Manual PNOZ mm0p-T 1002704-EN-0113InstallationControl cabinet installation} The unit should be installed in a control cabinet w

InstallationOperating Manual PNOZ mm0p-T 1002704-EN-0114Mounting distancesWith control cabinet installation it is essential to maintain a certain dist

CommissioningOperating Manual PNOZ mm0p-T 1002704-EN-0115CommissioningGeneral wiring guidelinesThe wiring is defined in the circuit diagram in the Con

CommissioningOperating Manual PNOZ mm0p-T 1002704-EN-0116CAUTION!Switch off the product before inserting or exchanging the chip card.Make sure that yo

CommissioningOperating Manual PNOZ mm0p-T 1002704-EN-0117Load project via USB portProcedure:} Insert a chip card into the card slot on the base unit.

CommissioningOperating Manual PNOZ mm0p-T 1002704-EN-0118Reset circuit Input circuit without detection of shorts across contactsInput circuit with det

CommissioningOperating Manual PNOZ mm0p-T 1002704-EN-0119Feedback loop Redundant outputContacts from external contactorsCon

PrefaceThis document is the original document.All rights to this documentation are reserved by Pilz GmbH & Co. KG. Copies may be made for internal

OperationOperating Manual PNOZ mm0p-T 1002704-EN-0120OperationMessagesThe PNOZmulti control system is ready for operation when the "POWER" a

OperationOperating Manual PNOZ mm0p-T 1002704-EN-0121Restart PNOZmultiThe unit is in a STOP condition. Procedure for restarting the unit:} Press the

Technical detailsOperating Manual PNOZ mm0p-T 1002704-EN-0122Technical detailsGeneral 772010Approvals BG, CCC, CE, GOST, TÜV, cULus ListedElectrical d

Technical detailsOperating Manual PNOZ mm0p-T 1002704-EN-0123Inputs 772010Potential isolation NoTest pulse outputs 772010Number of test pulse outputs

Technical detailsOperating Manual PNOZ mm0p-T 1002704-EN-0124Environmental data 772010Frequency 10,0 - 150,0 HzMax. acceleration 1gAirgap creepageIn a

Technical detailsOperating Manual PNOZ mm0p-T 1002704-EN-0125Mechanical data 772010Stripping length 9 mmDimensionsHeight 100,0 mmWidth 45,0 mmDepth 12

Maximum capacitive load C (μF) with load current I (A) at the semiconductor outputsOperating Manual PNOZ mm0p-T 1002704-EN-0126Maximum capacitive load

Maximum permitted total current of the semiconductor outputsOperating Manual PNOZ mm0p-T 1002704-EN-0127Maximum permitted total current of the semicon

Order referenceOperating Manual PNOZ mm0p-T 1002704-EN-0128Order referenceOrder reference Product type Features Order no.PNOZ mm0p-T Base unit 772

...Sachnummer Printed in Germany © Pilz GmbH & Co. KG, 2011+49 711 [email protected] GmbH & Co. KGFelix-Wankel-Straße 27

ContentOperating Manual PNOZ mm0p-T 1002704-EN-013Section 1 Introduction 51.1 Validity of documentation 51.1.1 Retaining the documentation 51.2 Overvi

ContentOperating Manual PNOZ mm0p-T 1002704-EN-014Section 8 Technical details 228.1 Safety characteristic data 25Section 9 Maximum capacitive load C (

IntroductionOperating Manual PNOZ mm0p-T 1002704-EN-015IntroductionValidity of documentationThis documentation is valid for the product PNOZ mm0p-T. I

IntroductionOperating Manual PNOZ mm0p-T 1002704-EN-016Definition of symbolsInformation that is particularly important is identified as follows:DANGER

OverviewOperating Manual PNOZ mm0p-T 1002704-EN-017OverviewUnit structureRange} Base unit PNOZ mm0p-T} Documentation on data mediumUnit featuresUsin

OverviewOperating Manual PNOZ mm0p-T 1002704-EN-018– Error messages– Diagnostics– Supply voltage– State of the inputs– State of the outputs} Test

OverviewOperating Manual PNOZ mm0p-T 1002704-EN-019Legend} X1:– Inputs I8 ... I15} X2:– Configurable test pulse/auxiliary outputs T0M20 ... T3M23–